Contents
Specifications
Dimensions information
Full lenght machine
51.19ft in
Full height of vehicle:
24.18ft in
Wheelbase length (Distance between the foremost and rearmost wheels)
20.84ft in
Turning Radius of a vehicle:
49.87ft in
Width Over Tires-Front
24.68ft in
Width Over Tires-Rear
27.33ft in
Specifications
Electric Drive
Ratio
32.62:1
Alternator
GTA -39
Control
AC Torque Control System
Motorised Wheels
GDY106 Induction Traction Motors
Maximum Speed (Km/H)
64.5
Electrical System
Alternator
24 volt, 140 amp
Lighting
24 volt
Cranking Motors
Two/24 volt
Body
Capacity Struck
223.7yd3
Heaped (2:1, Sae)
276yd3
Payload
640328.2lb
Structure
Flat floor configuration
Weight
66936.8lb
Canopy Sheet
5 mm 0.19\’\’ 690 mPa 100,000 psi tensile strength steel
Front Sheet
9 mm 0.35” 1379 mPa 200,000 psi tensile strength steel
Side Sheet
8 mm 0.31” 1379 mPa 200,000 psi tensile strength stee
Floor Sheet
16 mm 0.63” 1379 mPa 200,000 psi tensile strength steel (two-piece)
Loading Height
23.2ft in
Engine specifications
How many cylinders does an engine have?
18
Brand
2238
Model
SSDA18V170
Revolutions Per Minute
1900rpm
Engine displacement
4759.9cu in
Fuel Type
Diesel
Weight
22266.7lb
Horse Power: Sae J1995
3501.5hp
Horse Power: Iso 9249 / Sae J1349
3345.9hp
Operating Cycle
4-cycle
Driveline
Service Brake Type
Oil-cooled, hydraulic-actuated, multiple disc brakes at each wheel.
Parking Brake Type
Multiple disc, spring-applied, hydraulically-released, dry brakes on inboard end of each wheel motor rotor shaft. Rated to hold on ±15% grade at maximum gross vehicle weight.
Emergency Brakes
Automatically applied prior to hydraulic system pressure dropping below level required to meet secondary stopping requirements.
Wheel Brake Locks
Switch-activated
Electric Dynamic Retarder (Max.)
4026
Max. Service Apply Pressure (Kpa)
2500.1psi
Total Friction Area Per Brake (Cm2)
97025 cm2 , 15038 in2
Capacities
Fuel Tank
1400.2gal
Cooling System
190gal
Hydraulic System
350.1gal
Crankcase
90.1gal
Motor Gear Box
25.1gal
Weights
Gross Weight
1114998.9lb
Empty Weight
474670.7lb
Weight Distribution Front – Empty
48.5%
Weight Distribution Rear – Empty
51.5%
Weight Distribution Front – Loaded
32.8%
Weight Distribution Rear – Loaded
67.2%
Tires
Standard Tire
53/80 R63
Hydraulic System specifications
Hoist Cylinder
Two 3-stage dual-acting outbound cylinders and internal cushion valve, over-centre damping.
Relief Pressure
Hoist and brake cooling- 17237 kPa 2,500 psi Steering and brake-25759 kPa 4,000 psi
Hoist Time
Power-up loaded: 21 sec; Power-down: 23 sec; Float-down empty:24 sec
Turning Circle Diameter (Sae)
97.7ft in
Reservoir
250gal
Filtration
In-line replaceable elements
Suction
Single, full flow, 100 mesh
Hoist And Steering
Dual, in-line, high pressure
Pumps
Two pumps, single package, end of alternator